Skip to content

About

Module Programming for the MkII FG FDIM via J2534 & USB

Topics

Resources

Code of conduct

Contributing

Security policy

Stars

2 stars

Watchers

1 watching

Forks

Repository files navigation

RightToRepair

FG2ICCFlash

This software is published freely in the spirit of Right to Repair. See the wiki for educational material.

What this is

This is a full spec engineering tool for use with the Ford MkII FG Falcon's Front Display Interface Module, aka the ICC, the Interior Command Centre. It replaces the Ford Dealership firmware reprogramming system, which is done via the Ford IDS software, which is broken for this procedure, and there is no chance in hell that Bosch Automotive Service Solutions(who are the actual maintainers of Ford IDS) will ever touch this functionality ever again, so here is a fully open source and substantive solution for performing Module Programming and Configuration and Firmware Recore on the MK2 ICC.

image

Who it's for

The reprogramming happens in two stages, the first via the CANbus(yes the OBD port) using an SAE J2534 PassThru Device, the second is via USB. The intent here is in the spirit of Right to Repair, and the project's mission is to help to extend the overall life that we get out of these units across the board. This project is aimed at the DIY folks at home, Independent Workshops and Ford Dealerships who need the functionality that they have lost to time back in a working state again. Also in addition the USB-Recore functionality is built out and a small linux scripting engine for developing custom payloads to recore, as well as community based firmware backups are selectable as a recore option, and navimaps.zip as well. Enjoy, hopefully this helps some folks save a few units from the bin.

Where it's at

We have a bench verified succesful OBD flash!
image

We have a bench verified succesful USB flash!
image

Requirements

  • A windows laptop with .NET 4.8.1 x86 installed.
  • An SAE J2534 PassThru Device with Ford MidSpeed CAN @ 125KBPS capability. Here, and here
  • A USB drive with at least 8 gigabytes of memory
  • The ability to fault find and troubleshoot will come in very handy, as will a can-do attitude - a DIY automotive noob IS capable of using this software

Instructions for use

Download the software from the releases page, and fire it up, plug in your J2534 device to USB and OBD, select it in the software, select your firmware and flash! Stage 2 via USB is explained within the tool. The software may be a bit daunting, but I have tried to keep it as user friendly as possible. If you come across a problem or a fault or a bug, please raise an issue in the repo issues section.
image

Diagnostics

Read and Clear DTC is available from the diagnostics tab, alongside both the On Demand Self Test and the EOL Assembly Self Test.

Configuration via EEPROM/As Built Data

There is a built in As Built Data editor in the tool, that allows you to set the module configuration options, programmed VIN and single/dual zone settings. This is currently untested. The tool will also load and save .ABT As Built files in the forscan format.

Firmware

A collection of firmware files have been provided for use with the software in PHF, Binary and Hex format, use as you will. I believe the -CS firmware is the FPV spec firmware, with extra EEPROM space. Official Firmware, Updates and Community pulled recore backups are available for download from within the Stage 2 tab of the tool, and are hosted at https://www.testerpresent.com.au/FDIM/

AR79-14D017-JL.phf Patched Firmware

For installs where MK2 FDIM going into MK1, this patched firmware provides CANbus compatibility
There are three modifications to this firmware from the original

  • Dimming from 0x128 is inverted to match the MK1 CANbus
  • Ambient Temperature grabbed from 0x353 is now rebroadcast on 0x313 Byte 0
  • HVAC Buttons on 0x307 are now aligned with what the MK1 expects

Brick risk

These Mark 2 FDIM's are extremely delicate and as such any use of this software may inexplicably brick the FDIM rendering it essentially useless. Use at your own risk, if you are unsure, contract the services of a suitably qualified Module Programmer to program the module. You can thank SWSA for that.

If you fucked up...

Professional Automotive Technical Support is available from Tester Present. How convenient! That's me!.

FFAU

FFAU

Failing ICC Thread: https://fordforums.com.au/showthread.php?t=11479908&page=2

Thanks

JasonACT for the extensive documentation and development effort put in over a long period of time. Most of this project is based on his work.

Get your anonsies

Open Sauce

Engineering Specification documentation regarding this controller was sourced via a guerilla diagnosticos group that reverse engineer without fear for the Right to Repair!

About

Module Programming for the MkII FG FDIM via J2534 & USB

Topics

Resources

Code of conduct

Contributing

Security policy

Stars

2 stars

Watchers

1 watching

Forks

Releases

Contributors

Languages