English | 中文
NM-CYD-C5 is a Cheap Yellow Display (CYD) based on ESP32-C5, supporting dual-band Wi-Fi 6 / BLE 5 / Thread / Zigbee.
This development board features an ESP32-C5 with a built-in 320 × 240 2.8" LCD touchscreen, similar to the ESP32-Cheap-Yellow-Display. The default LCD driver is ST7789, and it can also be changed to the ILI9341 driver.
The NM-CYD-C5 has the following features:
- ESP32-C5-WROOM-1, 16MB Flash and 8MB PSRAM
- 320 × 240 LCD Display (2.8")
- Resistive Touch Screen
- ESP32-C5 USB Type-C port and USB Type-C to UART port (CH340), for powering and programming
- SD Card Slot, RGB LED and some additional pins
- Fully compatible dimensions and interfaces with ESP32-Cheap-Yellow-Display, enabling seamless replacement
- FPC connector added for more convenient connection to external modules
- ESP32-C5 RISC-V 32-bit @ 240 MHz
- Dual-Band Wi-Fi 6: 2.4GHz & 5GHz (802.11ax)
- Bluetooth 5: Classic and BLE 5 with SPP, HID, GATT support
- IEEE 802.15.4: Zigbee 3.0 end-device support
- Thread: IPv6-based mesh networking protocol
| Component | Specification |
|---|---|
| Main SoC | ESP32-C5 (RISC-V 32-bit, 240MHz) |
| Wireless Protocols | Wi-Fi 6 (802.11ax) 2.4/5GHz + BLE 5.3 + IEEE 802.15.4 |
| Display | 2.8" TFT, 240×320, ST7789, Touch Screen |
| Memory | 16MB Flash + 8MB PSRAM |
| Interface | 2× USB-C, GPIO, Micro SD Card Slot |
You can get the NM-CYD-C5 from the RockBase IoT AliExpress store, the RockBase IoT official website, or from NMTech Stores.
For details on how to get started with your NM-CYD-C5, please check out the Setup and Configuration page.
To work with NM-CYD-C5, you should use the newest espressif32 library, version 3.3.5 or higher.
[env]
platform = https://github.com/pioarduino/platform-espressif32/releases/download/55.03.36/platform-espressif32.zip ; Arduino 3.3.6When you use TFT_eSPI to work with the LCD, you should add TFT_eSPI_ESP32_C5.c/h to the Processors directory, and update TFT_eSPI.c/h with CONFIG_IDF_TARGET_ESP32C5.
These files can be found in Demos\Arduino\libraries\TFT_eSPI.
| Device | SCK | MISO | MOSI | CS | IRQ |
|---|---|---|---|---|---|
| Display | 6 | 2 | 7 | 23 | --- |
| Touch | 6 | 2 | 7 | 1 | --- |
| SD Card | 6 | 2 | 7 | 10 | --- |
| Device | RX | TX | GPIO |
|---|---|---|---|
| GPS | 4 | 5 | --- |
| 1 | 2 | 3 | 4 |
|---|---|---|---|
| 3.3V | IO9 | IO8 | GND |
Note: IO8 and IO9 are used for the I2C bus and are pulled up on the board via R32 and R33 — please keep this in mind when using them.
| 1 | 2 | 3 | 4 |
|---|---|---|---|
| IO4 | IO8 | IO26 | GND |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| IO2 | IO6 | IO7 | IO10 | GND | IO4 | IO8 | IO5 | IO9 | USB D- | USB D+ | GND |
| NM-CYD-C5 | Pin |
|---|---|
| IO25 | Display BL |
| IO27 | WS2812 RGB LED |
The RockBase IoT Colorful Special Edition will be released soon and is compatible with the standard NM-CYD-C5.
In response to widespread user demand, the latest batch of NM-CYD-C5-Colorful includes a new external-antenna design, available as an option. The NM-CYD-C5-Colorful-Ant comes with an IPEX 1 cable and a dual-band 2.4G/5G antenna, making it easy to use an external antenna. The external-antenna version of the NM-CYD-C5-Colorful delivers better Wi-Fi and BLE signal reception, making it suitable for users with higher wireless-performance requirements.
- Frequency range: 2400~2500MHz / 5000~5800MHz
- VSWR: 2400-2500 ≤ 2.5, 5000-5800 ≤ 2.5
- Efficiency %: 2400-2500: 83.3 AVG; 5000-5800: 73.8 AVG
- Peak Gain (dBi): 2400-2500: 3.2 AVG; 5000-5800: 3.7 AVG
- Radiation Properties: Omni-directional
- Polarization: Linear
![]() |
![]() |
![]() |
| Feature | Standard CYD (ESP32) | NM-CYD-C5 |
|---|---|---|
| Wi-Fi Band | 2.4GHz | 2.4+5GHz |
| Wi-Fi Standard | 802.11 b/g/n | 802.11ax (Wi-Fi 6) |
| ZigBee | None | ZigBee 3.0 |
| Thread | None | Thread 1.3 |
| Flash | 4MB | 16MB |
| PSRAM | None | 8MB |
-
Rogue Radar is a handheld ESP32 firmware that combines multiple wireless and utility tools into one rotary-driven interface.
-
Cheap Yellow Monster is a portable, touchscreen-driven WiFi security toolkit running on the NM-CYD-C5.
-
Application launcher for M5Stack, Lilygo, CYDs, Marauder and ESP32 devices.
-
GhostESP is an ESP32-based wireless security tool that integrates a variety of Wi-Fi attack and analysis features.
-
Espectre is an open-source platform combining ready-to-flash firmware, an embeddable C++ SDK, a MicroPython implementation, browser tools, a host-side CLI, open datasets, open model weights, and research workflows for building and validating detectors. It performs radio-based human presence detection using WiFi CSI and can connect to Home Assistant via ESPHome or MQTT.
-
ESP-Claw is Espressif's chat-coding AI agent framework for IoT devices. It defines device behavior through conversation and completes the full loop of sensing, decision-making, and execution locally on Espressif chips. Inspired by the OpenClaw concept and reimplemented in C, ESP-Claw is lightweight, intelligent, and continuously evolving.
New Version Released: ESP-Claw 0.3.0 has been updated to support NM-CYD-C5, merging new features from
espressif/master.
If you just want to flash the firmware, you can try the RockBase IoT Web Flasher and choose device type nm-cyd-c5.
If you would like your firmware or project to run on the NM-CYD-C5, please contact the RockBase IoT team and we will assist you with adaptation and testing.
For firmware you would like to offer as a download on our Web Flasher, please check out the ESPWebApps project. ESPWebApps is a web application management platform based on ESP32 that allows users to run and manage multiple web applications on the ESP32. With ESPWebApps, you can easily share your projects with NM-CYD-C5 users, making it simple to download, install, update, and run applications on the NM-CYD-C5.
-
The Original HaleHound-CYD Project closed the source codes, so this repository trying to continue the development and adaptation for the NM-CYD-C5.
-
The Poom is adapted from the the_pom multitool firmware for the NM-CYD-C5.
- Added new supported projects:
- Added a note about the IO8 and IO9 pull-up resistors, in response to issue #6. Thanks to SantaClaus1206 for the feedback.
- Added a note about using
#define TFT_INVERSION_OFFin Arduino, in response to issue #3. Thanks to ludodefgh for the feedback.
- Added the external-antenna version (
NM-CYD-C5-Colorful-Ant) description and antenna parameters. - Added external-antenna enclosure 3MF files:










